Planex FX-16NW Uživatelská příručka

16PORT FAST ETHERNT SWITCHING HUBENW-8300-T/2TFX-16NWJAPANhttp://www.planex.co.jpE-mail: [email protected], Win Kanda Takahashi Bldg1-7, Kand

9FX-16NW8FX-16NWThe VLAN feature of the Switching Hub lightens traffic on a network andstrengthens network security, all by dividing the original broa

11FX-16NW10FX-16NWBroadcast DomainAlthough a collision domain is divided by each of the ports on the Switch, abroadcast packet is still sent to all po

13FX-16NW12FX-16NWNote : Be sure to match ports in a Trunk in increasing order.Example : Port 1 through 4 in Trunk 1 of Hub A need to be linked to por

1514FX-16NWBefore proceeding, please take a minute to review the safety guidelinesdescribed in the Safety Instructions above. Also, be sure to follow

17FX-16NW16Installing the Switch in a 19” Rack1. Use the supplied screws to attach the metal fittings to the switching hub.2. Use the screws for the r

19FX-16NW18FX-16NWNote: Should you experience any problem in establishing a data link on any ofthe ports, please refer to Appendix A and B for troubl

2120FX-16NWAll the parameters and operational settings of VLAN, Trunking, SpanningTree and Port Mirroring features are configured through a terminalap

23The transfer mode of the port can be set to any of the following modes:[1]Auto [2]100Full [3]100Half [4]10Full [5]10Half Type the desired mode numbe

25FX-16NW24FX-16NW[2] Config spanning Tree SettingThis option allows you to specify the spanning tree protocol settings.Type “2” at the [Setup>] pr

27FX-16NW26FX-16NW[4] Set Hello TimeSpecifies the interval at which each spanning tree packet is sent within thenetwork. Enter “4” at the [Your selec

16PORT FAST ETHERNT SWITCHING HUBUSERS MANUALFX-16NW

29[4] Config Sniffer Port SettingModifies the current port mirroring settings.Type “4” at the [Setup>] prompt in the main menu, and press Enter. Th

31FX-16NW30FX-16NW[4] EXITReturns to the main menu.Type “4” at the [Your select>] prompt and press Enter.[5] Config Trunking Port SettingConfigures

33FX-16NW32FX-16NW[4] Port 1,5,2,6 four port trunkingSets Ports 1, 5, 2 and 6 to a trunking port. Type “4” at the [Your select>] prompt and press E

35FX-16NW34FX-16NW[3] Config Vlan by VidYou can select individual ports to form your own Vlan group. Note:To enable this option, you need to assign a

37FX-16NW36FX-16NW[4] Set Server PortAssigns a port to a server port. A server port belongs to all VLAN groups,and it is usually connected to a share

39FX-16NW38FX-16NW[8] Restore Default Switch SettingInitializes all the parameters to the factory-default settings.Type “8” at the [Setup>] prompt

4140FX-16NWThe FX-16NW can be easily monitored through its LED indicators. Pleasefollow the troubleshooting steps below to solve any problem you maye

43Technical Support for assistance.The STP ports on the FX-16NW support “Auto-Negotiation” feature. Thistechnology automatically sets the best possib

4544FX-16NWbetween the device and the FX-16NW.The Spanning Tree Protocol (STP) feature of the Switching Hubimplements intelligent fault-tolerance func

47FX-16NW46FX-16NWOrdinary data is finally sent at this stage. Spanning Tree Topology (Structure)A path cost refers to the relative “distance” betwe

Trademarks Copyright @1999 PLANEX COMMUNICATIONS INC.Contents subject to change without prior notice.Pci is a registered trademark of PLANEX COMMUNICA

49FX-16NW48FX-16NWanother link in the same segment. STP was developed as a countermeasure against loops generated in bridgedor switched networks. Whe

51configure STP with extreme caution. Standard Conformance : IEEE 802.3 10BASE-T,IEEE 802.3u 100BASE-TX, IEEE802.3DAccess Method :

52FX-16NW

a. The power cord or AC power adapter is damaged (or frayed). b. If liquid has been spilled into this product.c. The product does not operate normally

FX-16NWChapter 1 Introduction1 - 1P r oduct Overview... 12F e a t u res ...

1The FX-16NW 16 Port Fast Ethernet Switching Hub features sixteen10/100BASE-TX auto-negotiation switch ports. The Switch is rack-mountable, and fully

3FX-16NW2FX-16NWOpen the shipping carton of the Switching Hub and carefully unpack itscontents. The carton should contain the following items:FX-16NW

5FX-16NW4FX-16NW1-2 Rear PanelConsole Port : Connects to the supplied serial cable. The cable is in turnattached to a terminal(PC) for configuring the

7FX-16NW6FX-16NWSwitching schemeMost switching hubs support one of the following switching schemes: CutThrough or Store & Forward. In Cut Through